Mean, median and mode are the three averages you will meet in statistics class, and they tell you different things about a set of numbers. The mean is the average most people think of, the median is the middle value, and the mode is the most common value. Your TI-84 can work out all three in seconds with the 1-Var Stats tool, and it gives you a lot of other useful numbers at the same time. This guide shows you how to enter your data, run 1-Var Stats, and read the results.
What mean, median and mode tell you
The mean is the sum of all the values divided by how many values there are. If your test scores are 70, 80 and 90, the mean is (70 + 80 + 90) / 3, which is 80. The median is the middle value when the data is in order. For 70, 80 and 90, the median is 80. For an even number of values, like 70, 80, 90 and 100, the median is the average of the two middle values, 85. The mode is the value that appears most often. If your data is 5, 7, 7, 9, the mode is 7, because it appears twice and the others appear once.
These three averages can be different, and the difference tells you something about the data. If the mean is much higher than the median, a few large values are pulling the average up. If the mean and the median are close, the data is fairly symmetric. Your teacher will ask you to compare them, so it is worth knowing how to find all three quickly.
Step 1: enter your data in a list
Press [STAT] and choose 1: Edit. You will see the list editor, with columns L1, L2, L3 and so on. Move to L1 and type your data, pressing [ENTER] after each number. For our example, use the test scores 72, 85, 90, 78, 88, 95, 82. Type 72, press [ENTER], type 85, press [ENTER], and keep going until all seven scores are in L1. If L1 already has old data in it, clear it first. Move to the top of L1, where it says L1, press [CLEAR], and press [ENTER] to clear the whole list.
Check your data before you go any further. A single typing error, like 720 instead of 72, will make all your answers wrong, and the calculator will not warn you. Read the list through, compare it with the data in your question, and fix any mistakes by moving to the wrong number, typing the right one, and pressing [ENTER].
Step 2: run 1-Var Stats
Press [STAT] and press the right arrow to move to the CALC menu. Choose 1: 1-Var Stats. The calculator will ask you which list to use. If your data is in L1, which is the default, just press [ENTER] to calculate. If your data is in a different list, type the list name first. To type L1, press [2ND] then [1]. To type L2, press [2ND] then [2]. Then press [ENTER].
The calculator will show you a screen full of results. The first one is x-bar, which is the mean, written as x with a bar over it. For our test scores, the mean should be about 84.29. The next one is Σx, which is the sum of all the values, 590. Then Σx², which is the sum of the squares, and Sx and σx, which are the standard deviations, which we cover in a separate guide. Scroll down with the down arrow to see more results, including n, which is how many values there are, 7, and minX, Q1, Med, Q3 and maxX, which are the five number summary.
Reading the median and the mode
The median is shown as Med in the 1-Var Stats results. For our test scores, the median should be 85. That is the middle value when the scores are in order: 72, 78, 82, 85, 88, 90, 95. The middle one is the fourth one, 85. The calculator works that out for you, and it also gives you Q1 and Q3, which are the medians of the lower and upper halves of the data. Q1 should be 78 and Q3 should be 90 for our data.
The mode is not shown in the 1-Var Stats results, because the calculator does not work it out for you. To find the mode, look at your data in the list editor and count how often each value appears. For our test scores, every value appears once, so there is no mode. If your data is 5, 7, 7, 9, the mode is 7, because it appears twice. If two values appear the same number of times, the data has two modes, and you should write both down. The mode is the only one of the three averages you have to find by looking, not by calculating.
A worked example with a frequency list
Sometimes your data comes with frequencies, like a table that says the value 10 appears 3 times, the value 20 appears 5 times, and the value 30 appears 2 times. To work with that, put the values in L1 and the frequencies in L2. Press [STAT], choose 1: Edit, type 10, 20, 30 into L1, and type 3, 5, 2 into L2. Then press [STAT], go to CALC, choose 1: 1-Var Stats, and this time type L1, L2 before you press [ENTER]. To type L1, press [2ND] then [1]. To type the comma, press the comma key. To type L2, press [2ND] then [2]. Press [ENTER] and the calculator will work out the mean and median using the frequencies. The mean should be 19, because (10×3 + 20×5 + 30×2) / 10 is 19.
If you forget the frequency list, the calculator will treat each value as appearing once, and your mean will be wrong. Always check whether your data has frequencies, and if it does, put them in L2 and tell the calculator about them.
Common mistakes
The most common mistake is entering the data in the wrong list, or running 1-Var Stats on the wrong list. If your data is in L1 but you run 1-Var Stats on L2, you will get the statistics of an empty list or of old data, and your answers will be wrong. Always check which list your data is in, and make sure you tell the calculator to use that list. The second most common mistake is forgetting to clear an old list before you type new data, so your list has old numbers at the bottom that you did not notice. Clear L1 before you start, every time.
Another mistake is confusing Sx and σx, the two standard deviations. Sx is the sample standard deviation, and σx is the population standard deviation. For most school problems, your teacher will tell you which one to use, and it is usually Sx. If you are not sure, ask. A fourth mistake is reading x-bar as the median, or Med as the mean. X-bar is the mean, Med is the median, and they are different numbers. Read the labels carefully.
Try it yourself
Try these on your calculator. Enter the data 4, 8, 15, 16, 23, 42 into L1 and run 1-Var Stats. The mean should be 18, the median should be 15.5, and n should be 6. Enter the data 2, 2, 3, 5, 5, 5, 8 into L1 and run 1-Var Stats. The mean should be about 4.29, the median should be 5, and the mode, which you find by looking, should be 5. If you can do both, including finding the mode by looking at the list, you have the 1-Var Stats skill down, and you can use it for every statistics problem in your class.